Rossi-Blog Comment Discussion

  • sam12 so you are beginning to see things now as they really are? The e-cat SK ballerina emits some UV so could be used to sterilize hospital rooms contaminated by coronavirus. Or just buy a UV lamp as a cheaper option.

    I wish somebody with knowledge was with Rossi and SEE what he

    really does have by testing etc.

    It’s always just words, words and

    more words.Maybe if we’re lucky

    the people he says he is now

    working with provide the proof.

  • I wish somebody with knowledge was with Rossi and SEE what he

    really does have by testing etc.

    It’s always just words, words and

    more words.


    A few people with knowledge have tried to do that over the years, and pointed out mistakes in his measurement. They then get shown the door pretty quickly.

    • Colin Watters March 26, 2020 at 2:47 PM

      Dear Andrea, I was very interested in your reply to KiethT on the 25th March. He asked if the current safety testing completed the certification requirements for E-Cat domestic use and you replied yes. Can expand on your reply? Which standards will the E-Cat be certified as compliant with? If it will be CE marked, which EN standards specifically will it meet? Thanks.
    • Andrea Rossi March 26, 2020 at 3:22 PM

      Colin Watters:

      Please read better: KeithT did not ask if we have completed the certifications, he asked if the certifications will include etc, and I answered yes to this, not to what you say.

      The certifications are on course and have not been completed. Obviously they will be completed before we put in commerce the product, which means when the Ecat SKL will be ready to be put in commerce, and it is not now. Obviously, when the product will be in commerce the certifications will be made public, not before, for reasons that are obvious; everybody familiar with the matter knows that the procedures for certifications of products are always covered by NDA until they are granted and the trolls that are making a mess about this issue are paid by guys that are shooting their usual tennis balls to try to stop the carrier of our work.

      Warm Regards,


  • If memory serves from Rossi's blog, he was in Italy. Then he was not in Italy, but elsewhere in Europe. Perhaps he is back to Italy now.

    A man on the move.

    1. Sven B March 16, 2020 at 1:58 AM

      Dear Andrea Rossi,

      On February 9 you estimated the test to finish sometime in March.

      Now some questions on the new situation :

      1: Test starts in March?

      2: Test finishes in April?

      3: Test more likely finishes later than April?

      4: Are you now in Italy?

      5: Presentation still planned for Stockholm?

      6: Presentation more likely only Online?

      Kind regards

      Sven B

    2. Andrea Rossi March 16, 2020 at 4:54 AM

      Sven B:

      1 yes

      2 I do not know

      3 I do not know

      4 no

      5 yes

      6 this will depend on the corona virus consequences

      Warm Regards,


    1. Sven B March 22, 2020 at 11:15 AM

      Dear Andrea Rossi,

      Your comments today are very interesting:

      Recently you confirmed that you are staying in Europe but not in Italy.

      Now you say you are working in your own house.

      Have you got a house in Sweden?

      If not where in Europe are you staying at the moment?

      Kind regards

      Sven B

    2. Andrea Rossi March 22, 2020 at 11:34 AM

      Sven B.:

      For security reasons I have been suggested not to disclose where I am. I am in Europe.

      Warm Regards,


  • can ,

    The driver is the circuit from a small plasma globe. (Should fit into a cigarette pack). I bought two new globes for $20. The tube is cut from a vanilla bean container. To get glow discharge it was necessary to pump out the tube to about 26 in Hg. For that I used a Food Saver (I just undid the hose from the lid) combined with a large syringe and some one way fish tank valves (blue are best) as a roughing pump for the Food Saver. Horizontal clamps identical to Rossi’s are used to set the gap. A stainless steel U bolt was cut to obtain straight rods with threaded ends, smoothed, and these were threaded onto the clamps. Rubber stoppers were obtained from a hardware store, and drilled through for the rods with a sharpened metal tube.

    The left is negative, and is actually grounded to a wooden work bench.

  • Paradigmnoia

    Ingenious; thanks for the description.

    Is the gap adjustable while it's operating? I found that (at least at atmospheric pressures and probably somewhat larger currents than in your case) when the two brightest glow discharge regions at the anode and cathode meet each other at a close distance, RFI large enough to disrupt nearby devices can get produced. This would likely be easier to study/verify with a proper glow discharge setup at a low pressure, hence my interest. Although my GM counter didn't seem to show any noticeable change from the noise, it could possibly result in elevated signals with radiation monitoring equipment sensitive to electromagnetic interference.

    (This is probably off-topic for this thread)