Stevenson Verified User
-
Post
Stevenson Replied to the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop.
(Quote from Rob Woudenberg)
Not exactly: I tryed to load iron rods with electrolytic hydrogen (by using them as cathodes), but no plating was applied in that case. -
Post
Stevenson Replied to the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop.
In the previous weeks I tested a number of "variations" that do not produced any voltage (0.0 +-0.1 mV). These variation were for example loading plain iron rods with hydrogen (electrolytically), reloading my old WE with hydrogen (without plating), and… -
Post
Stevenson Replied to the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop.
(Quote from can)
Yes, some post-expiring experiments that I run where done with an iron oxide layer formed (not "thick" though) and hydrogen, either wet and dry. The experiment I run yesterday was done with the iron/iron oxide layer in place, and it was… -
Post
Stevenson Replied to the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop.
(Quote from can)
No doubt that the rought iron [oxide] layer will keep a significant amount of water. The point is that it is not sufficient to produce the effect. I specifically tested in the past to just wet the expired WE, and yesterday to… -
Post
Stevenson Replied to the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop.
Today I finally made a "reload" test: I tryed to load with electrolytic hydrogen my old LEC (the one that produced the effect in June, but then exausted due to hydrogen unloading and/or oxidation).
I placed the old WE in tap water together with an iron… -
Reaction (Post)
Stevenson Reacted with
to magicsound’s post in the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop. (Quote from Alan Smith)
Yes. For test6 I washed a new cathode tube in solvent, then pickled for 60 sec in 20% HCl and rinsed.
The plating solution was 16 g ferrous sulphate, 16 g sodium citrate and 18 ml 20% ammonia in 1 liter. A smooth coating of Iron was… -
Post
Stevenson Replied to the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop.
(Quote from THHuxleynew)
This kind of mechanism would allow a unidirectional current only (like in a diode). Instead the LEC is capable of conducting current in both directions, when an external voltage is applied. This current is linear up to a certain… -
Post
Stevenson Replied to the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop.
I found this interesting (and quite old) paper about iron plating:
https://nvlpubs.nist.gov/nistp…/18/jresv18n5p535_A1b.pdf
Contrary to the "traditional" recipe (the one based on sulphate, also suggested by Alan), here FeCl2 + HCl is used in order to… -
Reaction (Post)
Stevenson Reacted with
to Alan Smith’s post in the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop. -
Reaction (Post)
Stevenson Reacted with
to magicsound’s post in the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop. (Quote from Stevenson)
Following Alan Smith's suggestion, I used 25 grams each of Iron Sulphate and Sodium Citrate, buffered with 50 ml of Ammonia (20% concentration), all in 1 liter of distilled water. Magnetic stirring was used at slow speed for the… -
Post
Stevenson Replied to the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop.
(Quote from Rob Woudenberg)
This is something I wanted to try with my device (but didn't had time). -
Post
Stevenson Replied to the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop.
(Quote from magicsound)
Great news! The plot is really good and perfeclty aligned with other results we have seen. As expected (due to the dimensions of your device) the internal resistance is quite low. This means it is able to provide a greater current… -
Post
Stevenson Replied to the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop.
(Quote from Alan Smith)
Alan Smith, it is very important to verify if a current can be forced in vacuum by applying an external voltage (in one direction AND in the opposite). If no current is detected, or a very weak current compared to when the gas is… -
Reaction (Post)
Stevenson Reacted with
to Alan Smith’s post in the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop. Good day in the lab today- new 5-1/2 digit multimeter calibrated and talking to the data storage system, hydrogen generator brought back into action, and new (extra) feed-throughs in place on the vacuum chamber. -
Post
Stevenson Replied to the thread Garret Moddel’s ZPE Tapping Technology.
(Quote from Zephir_AWT)
Alexander Parkhomov describes in his book his experience and a number of well designed and fascinating experiments about PSI / paranormal. His conclusion (that is the same of many governament/military programs, such as the US… -
Post
Stevenson Replied to the thread Garret Moddel’s ZPE Tapping Technology.
I took a look at the Garret Moddel’s video and paper. His work is really well done either from a technological and scientific standpont, so it deserves for sure some attention. I don't know if the explaination of the small current and voltage is ZPE,… -
Post
Stevenson Replied to the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop.
Yes, but radiation from Americium is quite high energy. If the paper is correct, we can get low energy X-Rays, similar to the ones presumed in the LEC, with just a piezo tranduscer (that has the additional vantage that can be turned on and off). -
Post
Stevenson Replied to the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop.
(Quote from Ahlfors)
This paper is interesting for a couple of reasons:- they used an X-rays detector that has a good sensitivity in the low energy region (the Amptek-123), that is the region we are interested in for the LEC. They used a CdTe detector, but
-
Reaction (Post)
Stevenson Reacted with
to Ahlfors’s post in the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop. Micro-X-ray Sources from Flowing Gases -
Post
Stevenson Replied to the thread Frank Gordon's "Lattice Energy Converter (LEC)"...replicators workshop.
(Quote from magicsound)
Yes, you're right. I was aware and afraid of these problems (and other that are even more subtle) way before starting my replication. So I studied a number of possible solutions. However, in the end, when I made the actual…