Is a wire needed ? If a magnetron is being used as a direct feed to another capture device is there any purpose for a wire as an antenna ? or a clear passage best so not to destubed the rotation?
Seiber Troutman
Member
- Member since Oct 5th 2017
- Last Activity:
Posts by Seiber Troutman
-
-
Seen as a micro volcano driver,with some luck.
-
Just in case anyone mist the fundamentals~
5/27/18
I have bin practicing this build for years hoping I dont scrow it up now~
Printing some of the 'lost wax" style parts with a 3D printer I found it help to print the part on styrene, this is the best of the best after years of practicing.
Each time I use styrene - 020 or 030 ect, I shim the printer head with the same plastic to save my setting,
in all this is every odd thing you can think of to build the device, nickel bronze jaguar clyinder valve guides as for dust mixes, fishing wire and weed wacker filaments for casting, it never ends.
5-30 Perliminary Assemblies
The 3 printer parts are the in use designs" Cura 3D Printer" , This is the main mag set up.
http://science.sciencemag.org/content/352/6289/1087
op1 is just a magnetic for the clay/salt ect base
-
Pixie is just a mix of hematite and silver dust mixed with water-ion wash and let try. grind to re-dust it and put it in the microwave.
Assuming you know it ingnites, now run the ignited dust through another magnetron as a cathode, rotating stream.
At this point you can speculate the use of the now powered magnetron using this dust stream powers the mag.
the antenna area of this magnetron now feeds the flower and a excitonium reaction area to share the same exit.
You'r now using a excitonium reaction to power a magnetron.
-
Mods, please move the rhetoric, ty
-
Why are you associalatiing this to the tunnel generator I posted?
-
yeah. same old dead horse but the principles of building orbitz or layers on a object is fascinating.
-
SAFIRE is a good tattle-tale, of an effect. Good school~
-
-
External Content www.facebook.comContent embedded from external sources will not be displayed without your consent.Through the activation of external content, you agree that personal data may be transferred to third party platforms. We have provided more information on this in our privacy policy.External Content youtu.beContent embedded from external sources will not be displayed without your consent.Through the activation of external content, you agree that personal data may be transferred to third party platforms. We have provided more information on this in our privacy policy.
-
Preparing the pixie dust as a ballistic missile / wash float to clumps and re-crush. to fine but not micro dust.
A pre heat rotational magnetic feed to move the hematite "now with week magnetics after heating" into a spiral tightening upward cone.
To simulare this you would need a heat plate, a rotational collector that can also launch the newly heated partices. just to do the dust collection would be a cavity for the dust to fall in, use a heat base with a restricted inlet and a magnetic field to continue the tornadic rotation to keep the dust rising.
this plastic part as the void in a flat stone plate or clay - /melt out the [;astic and refill with mercury // high volt spark adjustable timing regulate the mercury's heat.
Beryllium Oxide caps after filling.
Same but its just a water pump for hematite. this is place over the heater to channel the dust. Stone/Clay/ ect.
At this point the hematite is hot and is being manipulated by a week magnetic field. To literally ignite the particle a magneton design could do it if its acks like silver in a common microwave
A common microwave magntron and cathode use magnets and the cath is design to shed electrons as the cathode heats and discharges in a rotation to fill the voids and create the wave leaving the antenna .
A new magnet field would need to be added on top of this flower to add muliple rotating magnetic within the flower, fields for each void to capture the wave and as they fill to capacity exit the same hole the hematite dust is moving through after being launched if this fllower was also atop the other parts.
For the rotaion field for the magntron, The same melt out plastic part insulated but impregnated above the flower magneton /again using mercury and a regulated spark discharge to control heat. At this point it would look like a acetylene torch spewing sparks up into the air.
entanglement within a magnetic field, As the particles can only handle so meny electron, collisions with each other and with a target can release energy? would you agree with this at this point?
as- put the last of this in here, to sustain this reaction the exit of the hematite is what feeds the magnetron. just attach the magnetron on top of the exit with the antennas down into the viod holes of the flower. A contstant self sustaining reaction until the dust looses its hydrogen. Providing it will be a sealed unit.
The Cathode for this is the path of the ignited dust in a rotating funnel.
-
-
If you all get stuck working with the hematite type cath Please give this a try,
cleaning up the clay for use was the post above to set up clay-hematite dust disks to fead a in line magnetron, the video of the object shows the wire in the back cut off Seems it run through the excitonium reaction as the cathode feeding a magnetron cav, and a carbon cap for discharge. And it seems copper is not the needed magnetic material, a track tube of hot mercury around the mag area was used looking at the evidence I chose from. {I know} the 3d printer accurately make this as small as it can be built,then build everything to it, looks like a 3 pc build.
magnetrons I know are not made from clay normally but added what it needs as dust mixes to firplace mortar is good practice and only need 500*- for A diamond tip I have no clue.
seems the road block is lifted.
-
I am curious if a slice of a cathode was design as a magnetron within the shaft with a magnetic rotating field at the area of this magnetron disk would it be more like a teslacoil or a magnetron?
-
-
Maybe in he 50 and 60 both technologes were clearly defined, one would hold Nations at Bay the other would defunk such , both would need to be clampdown until such a time. ..
-
I would ask him to participate, if he can. its not realy that much work at this point for him.
-
Agreed, I'm still a bit perplexed why he follow the 1959 example and stopped. He should have been able to get much farther in all this time with just a little bit of help. or for some reason wasn't allowed. it would not take much to get his toy running at least for short duration drone shoots to start the rest of it.
-
It sounds easy but I was a lot of reading...
-
Back to the top. Nice write-up Axil.