Interesting new battery prototype being tested in australia.
The Playground
-
-
Interesting what is efficiency way below, close to or over 1 according to Longmuir recombination calculations.
-
"The researchers' experiments showed that their small proton battery, with an active inside surface area of only 5.5 square centimetres, was already able to store as much energy per unit mass as commercially-available lithium ion batteries. This was before the battery had been optimised."
...Impressive.
-
http://news.newenergytimes.net/
When is Krivits going to stop bashing Hot Fusion, and get back to the LENR he knows best?
I do take issue with his aggressive style at times, but he does have a talent to dig up things few others have.
There is a lot going on now in LENR, with some good reports coming out of Japan and India, rumors about SKINR/Texas Tech, that needs some digging into.
-
I think Krivit is now making his living another way than by writing about LENR but I can't recall what it is. Nobody was as accurate and thorough about Rossi's past and his crimes than was Krivit.
-
Last phylanthropic debris from Industrial Heat LLC in Illinos
-
... and traces from an old hit [GHM + LH + LF]
-
Addenda
-
Scrap of info to add, I built casing from plaster of paris with ni heating wire within it hoping for a better cure
the attemp was drilling / fill/and cap the top and bottom after shrinking.
wire size was insufficient to penetrate the plaster for the needed temp.
continuing with this method with a more robust heating system.
about the same above but added the chips and carbon to crystal the whole structure only because they are so small.
edit in-
Realizing it may have bin a bit cryptic even from me srry
pics added
-
Back to the baghdad battery electrolyte plating.
-
Looks like IH's portfolio is starting to kick into gear. Good to see that. As Dewey said, he expects this year to be seminal. Speaking of....when are you coming back? We could use some of your eternal optimism to counter LR's eternal pessimism.
-
... another piss
-
Quote
Looks like IH's portfolio is starting to kick into gear. Good to see that. As Dewey said, he expects this year to be seminal.
Sure, Shane. And if not this year, why not next? I'm sure it will be, as they always say, "happening soon".
-
One of my more desperate attempts , mix in the middle with copper BBs as caps, spring load with a spring clamp and a hot wire voltage ac leads ~ dunk them after 24h
edit forgot the pic.
being to vague again..
I've used dissimilar material to add a type of galvanic corrosion to create the spaghetti effect and needs to be washed out before the electrlytes and witout dissolving the cath.
salt.
-
I can also canfirm, even with mixes I did not think possible turned back to dust.
-
Maybe washing with ion exchange resin defoulant water before initial assembly would help. it may have bin in the area at my first go around .
-
It sounds easy but I was a lot of reading...
-
If you all get stuck working with the hematite type cath Please give this a try,
cleaning up the clay for use was the post above to set up clay-hematite dust disks to fead a in line magnetron, the video of the object shows the wire in the back cut off Seems it run through the excitonium reaction as the cathode feeding a magnetron cav, and a carbon cap for discharge. And it seems copper is not the needed magnetic material, a track tube of hot mercury around the mag area was used looking at the evidence I chose from. {I know} the 3d printer accurately make this as small as it can be built,then build everything to it, looks like a 3 pc build.
magnetrons I know are not made from clay normally but added what it needs as dust mixes to firplace mortar is good practice and only need 500*- for A diamond tip I have no clue.
seems the road block is lifted.
-
Light coincidences
[left Russ George, right AR]
-
Snap2 is from this article:
http://atom-ecology.russgeorge.net/2013/05/04/edward-teller/
"My experiment was with deuterium gas, the nano-palladium in a tightly sealed thin glass cell in the presence of intense UV light which was an internal facet/product of the experiment. Naturally there were a few other tweaks."
This experiment must have been done before May 4, 2013.
An AWARE Geiger counter was used.
We are waiting for the gamma spectrometer to enter the stage ...
Want to Advertise or Sponsor LENR Forum?
CLICK HERE to contact us.
CLICK HERE to contact us.